23 hours 18 minutes
Hello. Welcome back, Tyson. Do you want interconnecting Cisco networking devices? Part one This episode 743 Configuring I P v six Sadiq routes. I am friend Donna Be instructor for this course. The last video. We would just went over the connected local routes How it compares to buy papers before and then we went and configured one and the demonstration.
In this episode, I'm going to be covering how to configure a static route for I p version six.
And like I said, So we're doing on this episode, Bridgeman could figure a static, wrote on the router one and rode her too, so we can reach each network.
So quick. Pre assessment here, what can be used for the fording part of the I P V six route command By that, if you remember the night people were forwarded a static route, we could do the next top address. We could do the outgoing interface. So which part do you think it can be used for? I b version six gave a few seconds.
All right, so we can actually use all three. We can use the link local, the global unit cast and the local outbound interface.
The thing is, with the local or the link local, we also have to include the phone interface. I'll show you here in a minute.
So we look at configure a static ground, it's configured it almost essentially the same way is an I. P version four route. We have I p V. Route. We add prefix
with prefects lengths. We tell it, you know, kind of what network is in, what direction.
So you tell it the L bone interface. We could tell the next global unit cast address
S O. You give two examples there. If we look at Roger one we could say to get to that 2112 a BCD three sub net, we would have to go through these cereals. Here's their zero,
uh, or we could put in that next hop address over outer two's serial address.
So I'm gonna go ahead and bring up the party session here. We get that going
and we see here, so if you do a show i p six interface brief. We should have cereal set up our any.
So what I'm gonna do here is
I wish I could configure aesthetic coats over to the dot threw the coal in three.
So I p v six routes
we want to do the 2112
a b c d
three colon slash
And I'm gonna tell this one to go out the serial
interface. We will set up the Global unit cast address on router to.
And now, if you take a look at the show I p version six routes,
we should see our aesthetic crowd in there with administrative distance of one off cereals. There is zero. So I'm gonna go ahead and plug in a round or two real quick.
All right, So if we go ahead and configure our two, let's get this going
figure terminal. I'm just going to a show.
You show I p v six
Okay, so, you know, interface figures, So let's go ahead and figures here. Zero
and I appear in six address.
This is 2112 a BCD 32
to slash 64
and I guess we can go out and just configure that I peer out real quick.
Six routes way. Want to go to 2112
and I want to send this one out the next IHOP address off 2112
maybe C d.
And that will be two going corn one.
All right. So, you know, we can see the difference in the i p routing table here,
so it's essentially a mirror is the same way, Um, as
the virgin forest. You know how this one is. Cereal.
This one is aesthetically set to this one.
So if we look at the Ping six command this time,
two and one
Come on, High Fever. Six.
You might have to have that same address is made her the same. Promise between 12 baby. See
All right, so we can ping that. All the device
sometimes pink six, Sometimes paying I peepers six. So no, it indifference.
We'll go over them or Indian trouble shooting one in the next episode.
So let's go ahead and could figure it just that basic interface i p for
the other networks. So interface I fe 00 This is the landside interface, remember?
So if we do, I hear six. Address
2112 a. B c. D.
Three. Colin, Colin one
Let's do a slash 64.
So I'm actually gonna go plug into Roger one again. I'm gonna configure the land side interface for that as well. For that, I p
all right. For your terminal
interface. Best season is zero people. Six
dress, 2112 maybe CD
so I'm gonna do a show. I'm gonna make sure that you get to route as well here.
All right, so we have a static over to that network,
so I'm gonna go ahead and do a ping.
20 months. Well, let's make sure we have that foreign network that we got around to it properly.
A B C D
All right. So we could hit that far network. We can route to it properly.
Um, setting up a static grounds. A simple Is that something good? Minimize party. Will movements of next slide.
So some other aesthetic drops that we can set up the default route is Theseus. Aim idea as your gateway of last resort. For I papers in six or epi, version four
is that route that sitting there saying if there's no other routes for your packet. Go ahead and send it through me. Send your
packet that you can't find a bath for through this interface.
Um, that's just with Cohen colon slash zero. Then you could give it the interface idea. It's the same thing. You can give it the global unit, CASS address.
Um, you can give it the interface I d and R. That host route, if you wanna get a specific route to a host, is just slash 1 28 instead of you know you instead of doing the
slash lease before. But this one, you'd actually give it to interface i d
and the command
and really floating static route. That's basically the same thing as the floaty site craft reputation for basically would set it up as a backup. I guess you could say I would say you have a you know, one gig line and you have a 10 meg line. You want all of your traffic to go through your tent or your you know, your gig line.
Well, you can have that 10 mag line,
but there is a backup you couldn't set to administer of distances to 54 as you can see in the
So stupid for
So, when are you gonna do to is if you have your interface set to auto configure If you remember, that was an option to get the I P. Address
than from slack early stateless address auto configuration
where it pulls that address, it can create an NDP route within the Ministry of Distance of two for that sub net for that on interface.
So this episode we went through the static route configuration. We went through a ping command. We made sure that our steady Krauts were actually working for the opposing sub nets are the prefixes.
Um and then we just set up a quick demonstration and we went through some of the other you know, floating static. Kraus and default rows forced static crosses of all.
So hopefully remember here, what is the administrative distance for a connected route? Give me a few seconds.
All right. It is zero. Remember, the static route is one
e i G R P is 90 and oh, SPF is one ton and weren't NDP is the new one with administrative since of two
and the next I was finished go ahead and show. Shoot an I p V for addressing and routes.
And as always, if you guys have questions, need help. Feel free to shoot the message. Always think for Washington's episode now forward a senior U. S um
Interconnecting Cisco Networking Devices Part 1 (ICND1)
Interconnecting Cisco Networking Devices Part 1 (ICND2) practice test helps prepare for the ICND2 100-105 ...
Cisco CCNA 100-105 ICND1: Interconnecting Cisco Networking Devices
Evolve your networking skills to fill the role of a core network engineer by using ...