[2018-June-New]CCNA 200-105 Dumps with PDF and VCE Free Share!Cisco CCNA Course

Begin Learning Cyber Security for FREE Now!

FREE REGISTRATION
Already a Member Login Here

Home Forums Courses Cisco CCNA Course [2018-June-New]CCNA 200-105 Dumps with PDF and VCE Free Share!

This topic contains 0 replies, has 1 voice, and was last updated by  Demiengineer 2 weeks, 2 days ago.

Viewing 1 post (of 1 total)
  • Author
    Posts
  • #119393

    Demiengineer
    Participant

    QUESTION 139
    In GLBP, which router will respond to client ARP requests?

    A. The active virtual gateway will reply with one of four possible virtual MAC addresses.
    B. All GLBP member routers will reply in round-robin fashion.
    C. The active virtual gateway will reply with its own hardware MAC address.
    D. The GLBP member routers will reply with one of four possible burned in hardware addresses.

    Answer: A

    QUESTION 140
    Which three statements about HSRP operation are true? (Choose three.)

    A. The virtual IP address and virtual MA+K44C address are active on the HSRP Master router.
    B. The HSRP default timers are a 3 second hello interval and a 10 second dead interval.
    C. HSRP supports only clear-text authentication.
    D. The HSRP virtual IP address must be on a different subnet than the routers’ interfaces on the same LAN.
    E. The HSRP virtual IP address must be the same as one of the router’s interface addresses on the LAN.
    F. HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing.

    Answer: BEF
    Explanation:
    The virtual MAC address of HSRP version 1 is 0000.0C07.ACxx, where xx is the HSRP group number in hexadecimal based on the respective interface. For example, HSRP group 10 uses the HSRP virtual MAC address of 0000.0C07.AC0A. HSRP version 2 uses a virtual MAC address of 0000.0C9F.FXXX (XXX: HSRP group in hexadecimal)
    All routers in a HSRP group send hello packets. By default, the hello timer is set to 3 seconds and the dead interval is 10 seconds. The range for HSRP version 1 is from 0 to 255. The range is for HSRP version 2 is from 0 to 4095. The default value is 0. For this question, it is assumed that Cisco is referring to HSRP version 1 as the other options are not correct.

    QUESTION 141
    What is a valid HSRP virtual MAC address?

    A. 0000.5E00.01A3
    B. 0007.B400.AE01
    C. 0000.0C07.AC15
    D. 0007.5E00.B301

    Answer: C

    QUESTION 143
    Refer to the exhibit. How should the FastEthernet0/1 ports on the 2950 model switches that are shown in the exhibit be configured to allow connectivity between all devices?

    A. The ports only need to be connected by a crossover cable.
    B. SwitchX(config)# interface fastethernet 0/1
    SwitchX(config-if)# switchport mode trunk
    C. SwitchX(config)# interface fastethernet 0/1
    SwitchX(config-if)# switchport mode access
    SwitchX(config-if)# switchport access vlan 1
    D. SwitchX(config)# interface fastethernet 0/1
    SwitchX(config-if)# switchport mode trunk
    SwitchX(config-if)# switchport trunk vlan 1
    SwitchX(config-if)# switchport trunk vlan 10
    SwitchX(config-if)# switchport trunk vlan 20

    Answer: B

    QUESTION 144
    Refer to the exhibit. A junior network engineer has prepared the exhibited configuration file.
    What two statements are true of the planned configuration for interface fa0/1? (Choose two.)

    A. The two FastEthernet interfaces will require NAT configured on two outside serial interfaces.
    B. Address translation on fa0/1 is not required for DMZ Devices to access the Internet.
    C. The fa0/1 IP address overlaps with the space used by s0/0.
    D. The fa0/1 IP address is invalid for the IP subnet on which it resides.
    E. Internet hosts may not initiate connections to DMZ Devices through the configuration that is shown.

    Answer: BE

    QUESTION 145
    Refer to the exhibit.
    Which statement describes DLCI 17?

    A. DLCI 17 describes the ISDN circuit between R2 and R3.
    B. DLCI 17 describes a PVC on R2. It cannot be used on R3 or R1.
    C. DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
    D. DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.

    Answer: C
    Explanation:
    DLCI stands for Data Link Connection Identifier. DLCI values are used on Frame Relay interfaces to distinguish between different virtual circuits. DLCIs have local significance because, the identifier references the point between the local router and the local Frame Relay switch to which the DLCI is connected.

    QUESTION 146
    What is the default Local Management Interface frame type transmitted by a Cisco router on a Frame Relay circuit?

    A. Q933a
    B. B8ZS
    C. IETF
    D. Cisco
    E. ANSI

    Answer: D

    QUESTION 147
    Refer to the exhibit. The network shown in the exhibit has just been installed. Host B can access the Internet, but it is unable to ping host C. What is the problem with this configuration?

    A. Host B should be in VLAN 13.
    B. The address of host C is incorrect.
    C. The gateway for host B is in a different subnet than the host is on.
    D. The switch port that sends VLAN 13 frames from the switch to the router is shut down.
    E. The switch port connected to the router is incorrectly configured as an access port.

    Answer: B

    QUESTION 148
    Which protocol provides a method of sharing VLAN configuration information between switches?

    A. VTP
    B. STP
    C. ISL
    D. 802.1Q
    E. VLSM

    Answer: A

    QUESTION 149
    Refer to the exhibit. What is the most appropriate summarization for these routes?
    A. 10.0.0.0 /21
    B. 10.0.0.0 /22
    C. 10.0.0.0 /23
    D. 10.0.0.0 /24

    Answer: B

    2018 Latest Cisco 200-105 Real Exam Questions PDF are Free Collected here: https://drive.google.com/drive/folders/0B75b5xYLjSSNeGdLM0gta2VVYm8?usp=sharing

Viewing 1 post (of 1 total)

You must be logged in to reply to this topic.

Our Revolution

We believe Cyber Security training should be free, for everyone, FOREVER. Everyone, everywhere, deserves the OPPORTUNITY to learn, begin and grow a career in this fascinating field. Therefore, Cybrary is a free community where people, companies and training come together to give everyone the ability to collaborate in an open source way that is revolutionizing the cyber security educational experience.

Cybrary On The Go

Get the Cybrary app for Android for online and offline viewing of our lessons.

Get it on Google Play
 

Support Cybrary

Donate Here to Get This Month's Donor Badge

 
Skip to toolbar

We recommend always using caution when following any link

Are you sure you want to continue?

Continue
Cancel