ICMP, Ping, and Trace-Route with UDP

March 9, 2018 | Views: 5670

Begin Learning Cyber Security for FREE Now!

FREE REGISTRATIONAlready a Member Login Here

 

In this article, I am going to share some basic information on ICMP, Ping and Trace-Route. Also see how UDP make use of ICMP for error communication.

First ICMP.

ICMP is a very simple, datagram-based protocol. Many other protocols rely up on ICMP to communicate the error conditions and hence it is mainly designed for error reporting and network-based troubleshooting . Now lets familiarize with ICMP code and type. The ICMP type field identifies what type of ICMP packet is being sent.

And the ICMP Code field provides much detailed information.

Common types of Code and Types are mentioned below.

Type 0 – Echo reply, which is usually the ping response. It says that the remote node is reachable over the network.

Type 3- Destination Unreachable, Which means the remote network or node is not reachable and there may be multiple reasons for that.

Btw, I have a very long story to say on ICMP Type 3, Code 3 and an affair with SNMP ,but not here ūüėõ .

Type 3 ICMP used the following codes.

  • ¬†¬†¬†Code 0: Network Unreachable
  • ¬†¬†¬†Code 1: Host Unreachable
  • ¬†¬†¬†Code 3: Port Unreachable
  • ¬†¬†¬†Code 9: Destination Network Administratively Prohibited

Here is a scenario on how other protocols use ICMP for error communications. Since UDP is a connection-less protocol, I will use UDP in this example.

If the requested UDP port is not an open port, then a “port unreachable” code may be returned

Consider a person is sending a UDP packet to a remote destination from his machine. Assume that, there is a firewall placed on the path that blocks this UDP traffic.So the Firewall blocks the packet to the next hop for a destination and a “network unreachable” code will be returned to the sending host. Similarly,if the Firewall allows the traffic, but the destination host simply doesn’t exist on the network, then a “host unreachable” code will be returned. However, if the host does exist on the network, but the requested UDP port is not an open port, then a “port unreachable” code may be returned by the intermediate device.

Type 5 – Redirect, Usually used to bring an update in routing tables.

Type 8- Echo Request, So when we do a ping, ICMP type 8 packet gets initiated. And the response for this will be a Type 0.

Type 11 – Time exceeded, usually occurs during a routing loop.

There are two codes associated with type 11.

  • ¬†¬†¬†Code 0: TTL Expired in transit
  • ¬†¬†¬†Code 1: TTL Expired during reassembly

Next let’s talk about Ping.

We all use this ping command to check the connectivity and reach on the network. Ping sends multiple ICMP Echo Request packets to the remote node and waits for their replies(Echo reply).

The ping command keeps track of when it sends the Echo Request packet and when it receives the corresponding Echo Reply. The difference between those two times is the round trip time. This is used to calculate the latency.

And finally, Trace-route

Trace-Route in Linux and Windows works differently

Trace-route maps the route/hops through which the packet traversed to reach the destination. Lets see how the Trace-route actually works. The command works by sending a series of packets all going towards the same destination, with TIL values starting at 1.When the first packet is sent, its TTL expires at the first hop, so the router(or the intermediate device) replies with an lCMP “Destination Unreachable” or “Time Exceeded” message. The trace-route command receives this reply and looks inside the payload for the lP address of the sender, which it assumes is the first hop’s router.Trace-route then sends a second packet, with a TIL of 2, which will expire at the second hop, generating another ICMP reply. Trace-route now knows the second hop as well. Similarly lt keeps sending packets this way, increment the TTL by 1 each time and getting replies from each hop until the packet reached the destination host.

In this way, it maps all the hops in between and helps the administrator to see the actual path.

Once major catch here is, the Linux Trace-route and Windows Trace-route works differently, Though they may produce similar results.

Trace-route on Linux/UNIX typically send UDP datagrams to random high numbered ports on the destination host.

Windows Trace-routs typically use ICMP Echo Request packets. But both the Linux and Windows methods generate ICMP error messages at the routers giving the same results.How? Remember, UDP uses ICMP for error communication.

Hope this provides a brief overview on ICMP, Ping and Trace-Route basics.

 

Share with Friends
FacebookTwitterGoogle+LinkedInEmail
Use Cybytes and
Tip the Author!
Join
Share with Friends
FacebookTwitterGoogle+LinkedInEmail
Ready to share your knowledge and expertise?
13 Comments
  1. very informative …………thanks a lot

  2. Concise and very informative
    Thanks

  3. Very helpful to day to day activity

Page 3 of 3«123
Comment on This

You must be logged in to post a comment.

Our Revolution

We believe Cyber Security training should be free, for everyone, FOREVER. Everyone, everywhere, deserves the OPPORTUNITY to learn, begin and grow a career in this fascinating field. Therefore, Cybrary is a free community where people, companies and training come together to give everyone the ability to collaborate in an open source way that is revolutionizing the cyber security educational experience.

Cybrary On The Go

Get the Cybrary app for Android for online and offline viewing of our lessons.

Get it on Google Play
 

Support Cybrary

Donate Here to Get This Month's Donor Badge

 
Skip to toolbar

We recommend always using caution when following any link

Are you sure you want to continue?

Continue
Cancel